*** Top
arp add
arp add host interface hardware-addr [options]
Options: UI means use AX.25 UI frames, I means use I frames.
~
arp drop
arp drop host interface
~
arp ignore
~
arp maxq (Parameter)
Maximum ARP requests waiting for response.
~
arp poll
~
arp retry (Parameter)
Number of times to retry an ARP check.
~
arp status
~
arp ui (Parameter)
arp ui on / off
By default, use UI frames else use I frames.
~
attach com (Startup)
attach com interface address vector speed [uart]
Attach a standard COM interface.
  attach com com1 0x3f8 4 1024 64 19200

The optional UART specification may be:
Spec   UART     RX TX FIFO size.
450  - 16450     0  0
550  - 16C550A  16 12
650  - 16C650   32 24
650A - 16C650A  32 16
654  - 16C654   64 48
850  - 16C850   64 48
950  - 16C950  128 96
~
attach kiss (Startup)
attach kiss interface com_interface channel speed
~
attach xkiss (Startup)
attach xkiss interface com_interface channel speed
~
attach ether (Startup)
attach ether ether_interface ax.25_interface interrupt 
~
ax25 ackdelay
ax25 ackdelay interface value
Acknowledge delay in milliseconds.
~
ax25 bbscall (Startup)
ax25 bbscall alias:call-ssid
Set bbs call and alias
~
ax25 frack
ax25 frack interface value
Wait for acknowledge in milliseconds.
~
ax25 maxframe
ax25 maxframe interface value
~
ax25 maxframee
ax25 maxframee interface value
~
ax25 mycall (Startup)
ax25 mycall alias:call-ssid
Set node call and alias
~
ax25 quality
ax25 quality interface value
~
ax25 qlimit
ax25 qlimit interface value
~
ax25 retry
ax25 retry interface value
Max retries
~
ax25 status
ax25 status [interface]
~
ax25 speed (Startup)
ax25 speed interface value
~
bbs (Process) (Local) (!Web)
~
bbs (Remote) (!Web)
~
bbsredir (Startup)
bbsredir callsign
In router only mode, the bbs command connects to the given call.
~
beacon
beacon TO interface file
If interface is 'all' the beacon is sent out all AX.25 interfaces.
~
bye (Remote) (!Web)
~
cookie
~
com mode (Local) (!Web)
com mode interface speed parity bits stop
~
com status
~
com term (Process) (Local) (!Web)
com term interface
~
com txtout (Parameter)
com txtout milliseconds
Timeout while awaiting an expected UART transmitter empty interrupt.
~
cron at
~
cron from
cron from start to end each interval at minute "command"
Example: cron from 00 to 23 each 30 at 5 "expire kick"
  start, end are hours, interval is in minutes.
~
cron status
~
cron sync (Process)
cron sync time-server
Synchronize the system clock with a Network time server,
e.g. tick.usno.navy.mil, tock.usno.navy.mil, ntp.ucsd.edu etc.
~
cron tout (Parameter)
Timeout waiting for time server response, in milliseconds.
~
disconnect (Local) (!Web)
disconnect session
~
domain clear
~
domain maxwait (Parameter)
domain maxwait value
Server timeout in seconds.
~
domain name (Parameter) (Startup)
~
domain server (Startup)
domain server <DNS server> [timeout in seconds]
~
domain status
~
domain translate (Parameter)
domain translate on/off
Translate IP addresses to host names.
~
domain ttl (Parameter)
domain ttl value
Seconds an unused domain cache entry is saved.
~
expire bid (Parameter)
expire bid value
Days until a BID is removed.
~
expire bulletin (Parameter)
expire bulletin value
Days until a bulletin is deleted.
~
expire group (Parameter)
expire group value
Days until inactive news groups is dropped.
~
expire nts (Parameter)
expire nts value
Days until undelivered NTS traffic returned.
~
expire personal (Parameter)
expire personal value
Days until unread personal message returned.
~
expire read (Parameter)
expire read value
Days until read personal message killed.
~
expire kick (Process)
~
http contout (Parameter)
http contout value
Connection timeout in seconds
~
http logintout (Parameter)
http logintout value
Login timeout in seconds
~
icmp latency (Parameter)
icmp latency value
How long to wait to send next ping after ping response received
~
icmp status
~
idle (Parameter)
idle value
Idle user timeout in seconds.
~
ifconfig description (Startup)
ifconfig description "The description of the interface"
~
ifconfig ipaddress (Startup)
ifconfig ipaddress interface address
~
ifconfig mtu
~
ifconfig netmask (Startup)
ifconfig netmask interface mask
~
ifconfig status
ifconfig status [interface]
~
ip address (Startup)
ip address system-default-address.
~
ip conn
~
ip heard
~
ip rtimer (Parameter)
ip frame reassembly timeout in seconds
~
ip status
~
ip ttl (Parameter)
ip time-to-live
~
kiss alloc (Parameter) (Startup)
kiss alloc size
KISS interrupt buffer allocation size.
~
kiss fullduplex
kiss fullduplex interface value
~
kiss persist
kiss persist interface value
~
kiss slottime
kiss slottime interface value
~
kiss txdelay
kiss txdelay interface value
~
kiss txtail
kiss txtail interface value
~
kiss update
~
locks
~
log expire (Parameter)
~
log ftp (Parameter)
~
log http (Parameter)
~
~
log proc (Parameter)
~
log rt (Parameter)
~
mbox archive (Parameter)
Archive all incoming messages?
~
mbox batch (Parameter)
mbox batch size
MailBox forwarding batch size
~
mbox forward (Process)
~
mbox haddress (Parameter) (Startup)
MailBox hierarchical address
~
mbox import (Process)
mbox import file
Import messages from file.
~
mbox lidlist
~
mbox poll (Process)
~
memory files
~
memory free
~
memory status
~
monitor connects
~
monitor close
~
monitor file
monitor file filename
Open a monitor log file.
~
monitor heard
~
monitor hflush
~
monitor hsize
monitor hsize entries
Maximum heard calls to retain.
~
monitor host
monitor host hostname:port
e.g. monitor host hank:8002
~
monitor off
monitor off interface
Turn off monitoring for the interface.
~
monitor on
monitor on interface options
Turn on monitoring for the interface.
Options:
text - Show frames in plain text.
hex  - Show frames in hex.
in   - Show received frames.
out  - Show transmitted frames.
Both text and hex may be specified.
If neither is specified only headers are shown.
~
monitor show (Process) (Local) (!Web)
~
monitor status
~
monitor tout (Parameter)
monitor timeout n
Number of seconds to wait for a connection to SockViewPort.
~
monitor twait (Parameter)
monitor twait n
Number of seconds to wait between attempts to connect to SockViewPort.
~
msgs (Parameter) (Startup)
~
netrom ackdelay (Parameter)
Acknowledge delay in milliseconds.
~
netrom bcnodes (Process)
netrom bcnodes interface
~
netrom bcdead (Parameter)
Remove dead node entry after this many seconds.
~
netrom blimit (Parameter)
Retry backoff limit.
~
netrom frack (Parameter)
Initial retry backoff in milliseconds.
~
netrom id
~
netrom ignore
~
netrom ignorebc
~
netrom maxframe (Parameter)
Window (frames)
~
netrom minqual (Parameter)
Minimum quality to include in node broadcast.
~
netrom nodes
~
netrom ports
~
netrom qlimit (Parameter)
NET/ROM receive queue limit in bytes.
~
netrom routes
~
netrom retry (Parameter)
~
netrom status
~
netrom ttl (Parameter)
Time to live
~
node (Process) (Local) (!Web)
~
node (Remote) (!Web)
~
nw go (Process)
~
nw routetout (Parameter)
Route timeout in seconds.
~
nw kill
~
nw hoptout (Parameter)
nw hoptout
Hop timeout in seconds.
~
nw rttmult (Parameter)
nw rttmul value
RTT multiplier
~
nw status
~
nw tries (Parameter)
Max attempts to reach node
~
nw usecall (Parameter)
nw use
Use random calls
~
ping (Local) (!Web)
ping host [timeout [latency [file]]]
  timeout and latency are in milliseconds
~
ping (Remote) (!Web)
ping host
~
pkstat
~
ps
~
qth
QTH requires a callsign, for example:
  qth ka7qrm
~
reset
~
restart
~
rewrite
~
rip add
rip add destination [flags]
  Flags: psu - Poisoned reverse, Split horizon, Us
~
rip auto (Parameter)
rip auto on/off
Automatic arp / route discovery.
~
rip drop
rip drop destination
~
rip kick
~
rip merge (Parameter)
rip merging on/off
~
rip poison (Parameter)
rip poison on/off
Poisoned reverse.
~
rip request
~
rip split (Parameter)
rip split on/off
Split horizon.
~
rip status
~
route add
route add destination[/<bits>] interface [gateway | direct [metric]]
~
route addprivate
route addprivate destination[/bits] interface [gateway | direct [metric]]
~
route check
route check destination
~
route drop
route drop destination[/bits]
~
route status
~
route ttl (Startup)
route ttl interface-type timeout
Where interface-type is "ether", "ax25" or "netrom"
and timeout is in seconds.
~
route wait (Startup)
route wait interface-type timeout
Where interface-type is "ether", "ax25" or "netrom"
and timeout is in seconds.
~
rt kill
~
rt link
rt link alias:call
~
rt status
~
socket
~
status
~
tcp blimit (Parameter)
tcp blimit value
Backoff limit.
~
tcp irtt
Minimum retry timeout in milliseconds
~
tcp maxwait
Maximum retry wait in milliseconds
~
tcp mss
tcp maximum segment size.
~
tcp reset
tcp reset <control block>
~
tcp retries
tcp retry limit.
~
tcp status
~
tcp window
tcp window.
~
udp
~
video main (Startup)
video window foreground background
Set window colors.
Background or foreground:
black blue green cyan red magenta brown lightgray
Foreground only:
darkgray lightblue lightgreen lightcyan lightred lightmagenta yellow white
~
video mainst (Startup)
video window foreground background
Set window colors.
Background or foreground:
black blue green cyan red magenta brown lightgray
Foreground only:
darkgray lightblue lightgreen lightcyan lightred lightmagenta yellow white
~
video sessionst (Startup)
video window foreground background
Set window colors.
Background or foreground:
black blue green cyan red magenta brown lightgray
Foreground only:
darkgray lightblue lightgreen lightcyan lightred lightmagenta yellow white
~
wp clean (Process)
~
wp edit (!Web)
WP edit callsign
~
wp global (Parameter)
~
wp list
wp list options:
all     - All entries
b       - BBS systems
c       - Users that have logged in
f age   - Older than age days\n");
n age   - New in last age days
s       - Sysops
u age   - Seen in last age days
x       - Excluded
@ where - BBS or location
~
wp query
~
wp status
~
wp update (Parameter)
~
?
~
.
Run a macro.
.file will run the commands in a file named file.cmd.
.file.ext will run the commands in that file.
~
*** Node
bye
~
bbs
~
connect
~
cookie
~
info
~
iconn
~
iheard
~
istat
~
link
~
mconn
~
mheard
~
nodes
~
ports
~
ping
~
qth
QTH requires a callsign, for example:
  qth ka7qrm
~
routes
~
rip
~
rt
~
*rtl
~
status
~
sysop (Sysop)
~
telnet
~
users
~
wp list
wp list options:
all     - All entries
b       - BBS systems
c       - Users that have logged in
f age   - Older than age days\n");
n age   - New in last age days
s       - Sysops
u age   - Seen in last age days
x       - Excluded
@ where - BBS or location
~
wp query
wp query list-of-callsigns
~
wp status
~
zip
Zip takes a zip code or range of zip codes, for example:
  zip 97140
  zip 97140 97145
~
?
Bye      Disconnect.
Connect  Connect to another node or station.
Info     Info about this system.
IConn    Display IP addresses of recent connects.
IHeard   Display IP addresses heard.
IStatus  Display IP address routing tables.
LInk     Display AX.25 interface performance table.
MConn    Display AX.25 callsigns of recent connects.
MHeard   Display AX.25 callsigns heard.
Nodes    Display NET/ROM node list.
Ports    Display ports.
PIng     Check connectivity to another node.
Routes   Display NET/ROM route list.
RIp      Display RIP statistics.
Status   Display system status.
Telnet   Connect to another node or station.
Users    Display connected users.

These commands may also be available:

BBs      Access the BBS, if it is available.
Cookie   Get a cookie.
Qth      Lookup information about a callsign.
RT       Access the RoundTable.
SYsop    Administer the system.
wp       Query the White Pages database.
Zip      Lookup callsigns by zip code.
~
*** BBS
bye
~
cookie
~
?h
h  n    - hold message number n. Accepts a list of message numbers.
~
info
~
?k
kill msg#
k  n    - Kill message number n. Accepts a list of message numbers.
km      - Kill my read messages.
k> tag  - Kill all messages to tag.
k< tag  - Kill all messages from tag.
kh      - Kill all held messages.
~
k@ (Sysop)
Kill by from, to or @ requires a call, for example:
  k> n7qrm
  k< n7qrm
  k@ n7qrm
~
k< (Sysop)
Kill by from, to or @ requires a call, for example:
  k> n7qrm
  k< n7qrm
  k@ n7qrm
~
k> (Sysop)
Kill by from, to or @ requires a call, for example:
  k> n7qrm
  k< n7qrm
  k@ n7qrm
~
kh (Sysop)
~
kind (Sysop)
kind id kind
Change message kind (B, P, T).
~
km
~
?l
l     - List messages new since last login.
lc    - List catagories of messages on the system.
lf n  - List first n messages.
lh    - List held messages.
lk    - List killed messages.
ll n  - List last n messages.
lm    - List messages addressed to you.
lp    - List personal messages.
lt    - List NTS messages.
l@ tag
l> to
l< from
~
?n
n       - Show your White Pages information.
n  Name - Set your name.
nh BBS  - Set your home BBS call.
nl n    - Set pause after each n lines.
nq qth  - Set your QTH.
~
node
~
?r
r  n - Read message number n.
rh n - Read message number n, show all headers.
~
rh
r  n - Read message number n.
rh n - Read message number n, show all headers.
~
rt (Sysop)
~
?s
sb  - Send a bulletin.
sp  - Send a personal message.
st  - Send NTS traffic.
sr  - Send a reply to the last message read.
~
sb
sb topic@distribution.
~
sp
sp call@bbs.hloc
~
sr
~
st
st zip@ntsxx
~
sysop (Sysop)
~
tag (Sysop)
Tag requires a message number and the new tag, for example:
  tag 555 k7iqi
~
uh (Sysop)
~
wp list
wp list options:
all     - All entries
b       - BBS systems
c       - Users that have logged in
f age   - Older than age days\n");
n age   - New in last age days
s       - Sysops
u age   - Seen in last age days
x       - Excluded
@ where - BBS or location
~
wp query
wp query list-of-callsigns
~
wp status
~
?
bye   - Disconnect.
info  - System information.
node  - Return to node.
sysop - Administer the system.
wp    - Query the White Pages database.

k commands: Kill messages. Use ?k for details.
l comamnds: List messages. Use ?l for details.
r commands: Read messages. Use ?r for details.
s commands: Send messages. Use ?s for details.
n commands: Your White Pages information. Use ?n for details.

Add a + to an l command to see forwards. e.g. ll 12 +
h  n    - Hold/Unhold message number n. Accepts a list of message numbers.
k  n    - Kill/Unkill message number n. Accepts a list of message numbers.
kh      - Kill all held messages.
uh      - Release all held messages.
k> to   - Kill all messages with specific To.
k< from - Kill all messages with specific From.
rt n    - Return message n to sender.
tag n newtag - Change message n tag.
kind n B|P|T - Change message n kind.
~
. (Sysop)
Run a macro.
.file will run the commands in a file named file.cmd.
.file.ext will run the commands in that file.
~